RC232 Q&A
Enter your keywords to find answers:
Technical questions from customers, answered by Radiocrafts' support engineers, about RC232 modules.
No questions match your filter.
01Why is RC1280HP-RC232 shown as ‘Not recommended for new designs’? How much longer will be in production?
RC1280HP-RC232 is not recommended for new design as you will have the RC1780HP-RC232 with benefits like smaller size and improved sensitivity. For existing RC1280HP costumer however the best approach is to continue using RC1280HP since the packet format is different and they do not communicate with RC1780HP. RC1780HP improved performance depends of different packet format since it is a different architecture. Please note that we have no plans of obsolete the RC1280HP for existing costumer as long as we are able to source all the parts used to build the module.
02Which RC232 module is recommend for India?
With regard to India and our module solutions that support the 865-867MHz range I would recommend you to specifically take a look at our RC1170HP-RC232 module that is designed for the Indian market.
03Where do I read the product ID + min. HW revision + FW revision?
The product ID + min. HW revision + FW revision are stored as a continuous string starting from address 0x3C. It could bel be “RC1140-RC232,2.00,1.31”.
However, please note that for instance the High Power (HP) variant of the module will have “RC11xxHP-RC232,x.xx,y.yy” product ID, and thus the HW and FW revisions will have different offset from address 0x39.
The product ID + min. HW revision + FW revision are stored as a continuous string starting from address 0x3C. In this case it will be “RC1140-RC232,2.00,1.31”.
04When there is message collision, will the CRC check fail? How do we enable CRC checking?
The CRC will filter out corrupted messages due to collision. If the CRC calculation fails the received data will be declined and not send out on the TXD. CRC is default on but can be switched off by CRC_MODE=0. For details see data sheet page 13
05When the module is receiving data from the air, is it possible to send data from the host on the UART RXD ?
" No, module does not listen to UART RXD when data is received from the air.
You can use HW handshake on UART to identify when this is happening."
06When the MAC layer has a packet to send, it will use a carrier-sense-multiple-access (CSMA) protocol to determine if another module is already transmitting. If another module is transmitting, the module will receive that data before attempting to transmit its data again. If, during this process, the UART receive buffer gets full, the CTS line will go high to prevent the host UART from over-running the receive buffer. The CSMA mechanism introduces a variable delay to the transmission channel. This delay is the sum of a random period and a weighted period that is dependent on the number of times that the module has tried and failed to acquire the channel. For applications that guarantee that only one module will be transmitting at any given time, the CSMA mechanism can be turned off to avoid this delay.
Thank you for your interest in our product. You will not find a CSMA or LBT algorithm embedded in our RC232 protocol. However all of our modules provide RSSI (Receiver Signal Strength Indicator) that your host MCU can be used as input when making your own Listen Before talk algorithm.
07When I set the transmit power to the smallest value, is only the transmit power reduced or also the receive power?
The output power in TX is programmable, and will not influence on the receiver. The receiver will receive packets as long as the incoming signal is inside the dynamic range limited by the sensitivity limit (weak signal) and the saturation level (Strong signal). You can use the RSSI to measure the signal strength of the received packet.
08When I connect RXEN and TXEN to VDD, instead of leaving open, the current consumption increases to 20, mA. When I send a character to the module over RS232, the current appears to be 134mA.
20 mA idle current is normal, but 135 mA in TX is to much. ON/OFF must be connected to VCC. Please follow the Data sheet recommendation for pin connection at all time.
09When CRC is enabled does the module try to resend the message if CRC does not match or is the message dropped?
The module do not have embedded retransmission. This must be handled outside the module in the host controller if needed.
10When a packet is transmitted from one module to another, what is the receiving module going to output on its UART? The exact number of bytes sent? Or will it add some extra information like “Byte count, sender address or CRC”?
The RC232 protocol is transparent: What you send in on one side , is what you get out on the other side. CRC is calculated, added, checked and removed by the module.
11What type of modulation type in the RC1190-RC232?
RC1190-RC232 use GFSK modulation.
12What the Radiocrafts SoM consist of (inside) ?
Inside the module is confidential information and part of our IP. You will get or the thecnical specification of the module from our data sheet.
13What should I check to confirmt that my module is correct connected
Pull ON/OFF pin high for power ON the module, CONFIG must be pulled high when not in CONGIG mode, Connect RXEN and TXEN directly to VDD if you will not use hardware enabling of SLEEP mode. Software activated SLEEP using Z-command will still work.
14What is the Tx current if I change the Output power?
For RC1740 you can tune the output power from +15 dBm to typ -10 dBm. TX current will be reduced if ourtput power is reduced. At 0 dBm it will be typ 35 mA.
15What is the range of the module RC1180-RC232 868 MHz? Can this module communicate over a distance of 500m?
Line of sight the range is around 5-700m, at lowest RF data rate. The range is heavily depending on the obstacles (if any) in the transmission path and as well if the antenna height
can be above 2m over the ground (the higher the better).
An alternative is to use the RC1180HP (500mW version, same footprint), but of course this module drains more current so it might not suite your application. Range line of sight with 500mW is 2-3 km.
16What is the range of RC1190-RC232 at 0dBm and 19kbit/s?
The RC1190 at max output power (-1 dBm) and 19 kbps should give around 150 meter using the Radiocrafts demo boards including the quart wave antenna. If you reduce the data rate to 1.2 kbps you should get around 300 meters due to the sensitivity improvement.
17What is the maximum output power for RC1190-RC232 in 900MHz band, 5dBm or 9dBm?
Upper two settings for power is correctly +5 dBm and +9 dBm. Max output for FCC compliance is -1 dBm and upper setting is for this reason not recommended.
18What is the expected range of the RC1190-RC232 module when implemented with a reasonable antenna solution?
Range is given by the TX output power, the RX sensitivity and the antenna gain. To improve the RX sensitivity you can reduce the data rate and typically 6 dB sensitivity improving will give twice the range. When it comes to chip antenna, we experience reduced performance (typ 30% range reduction) compare to quarter wave whip. Please also be informed that you can make an antenna at 915 MHz using a simple wire or PCB track of 7.8 cm. You can try to replace your chip antenna with 7.8 cm Wire to get an indication of your chip antenna performance. We have used the 868 MHz chip antenna from Fractus in our range testing.
19What is the estimated range on 433mhz @27db 19.2kps, 868mhz @27db 19.2kps?
Note again to follow national regulation. In EU +27 dBm at 433 MHz is not allowed. +27 dBm at 868 MHz will typ give 5 km free line of sight if configured for ultra-narrow band low data rate setting.
20What is the data transmission rate of the 1180HP at 5 km ?
We used 19.0 kbps during our range test.
21What happens if message buffer of 128 bytes gets completely full?
If max bytes limit is reach the module will transmit the bytes, and not include the rest of the bytes.
22What do you mean by peer-to-peer communication ?
The same as point to point communication.
23What are the LEDs for? They are not included In the RC2500 datasheet
They are not in use for –RC232 protocol but is used with Tinymesh protocol, so for –RC232 they do not need to be mounted.
24We’d like one of the LED outputs to blink on radio transmission, and the other LED output to blink on radio receive. It appears they are currently unused?
LED control is possible to include in a costumer specific variant.
25we use your Radiocrafts Modules (1180-RC232) and have problems with the configuration. Could you send us an example in C how to handle this?
We do not have source code for configuring the module, but information is documented in the data sheet.
26We use 2 Radiocrafts devices on the same board, do I need an extra EMI cage as shielding to avoid any EMI issues?
Additional EMI cage will not give much of improvement. The module is shielded already and EMI coupling will eventually go from antenna to antenna. This can obviously not be shielded, but placement will make a difference. If possible, the best approach is to have the module on each side of the board and separated with a solid ground plane.
27We need bidirectional repeater/router for our 2.4GHz system
A VHF radio, narrowband with high output power will have a lot better range than 2.45 GHz . You may consider to avoid the repeaters. Our experience from metering systems is that repeaters are nice in theory by a mess in the field… where to install, permissions to sites, who pay the powre if mains connected…. This is the reason 169 MHz is having a major success – no repeaters needed.
28We are trying to configure our modems RC2500HP 201545H to use them at a data rate of 250kbit/s, following the datasheet rev 1.22. However the communication fails at this RF rate. Back to 100 kbit/s the communication is works again.
Assuming this is RC2500HP-RC232, this has a max datarate on RF of 100kb/s.
This is given in first page of datasheet.
I know that the configuration information in datasheet give info on how to setup 250kb/s, which can be misleading.
29We are in the process of evaluating the RC1240, The only thing I’m not sure about at the moment is how to implement a busy check before transmitting
We are in the process of evaluating the RC1240, The only thing I’m not sure about at the moment is how to implement a busy check before transmitting
30Using a switching power supply from 12V to 3.3V, switching at 300 kHz, and a 1% ripple output; do I need extra filtering?
Inside the module we have only a 2u2 cap close to the VCC pins. The Radio part has an internal regulator but the Power Amplifier stages has not. For this reason a switching power might influence on performance and additional filtering should be added. Testing will inform if additional filtering is needed in your design.
31They have 10’s of sensors that assembled in a system, would like to consider to have low power RF units that can work in noisy and industrial zone. The system length could be <10m. A mesh is also something they could consider, please advise if you have experience in such application field
With all devices with <10 meter I do not see the need for mesh.
Also, it sensor are battery powered they are not suitable for routing.
To have a mesh they need a number of mains-powered devices.
I would look at a narrowband radio like RC1740-RC232/RC1780-RC232.
Frequency depend on were final equipment will be operating.
A narrowband radio is less likely to be interfered be other noise in the environment.
We have sold narrowband solution to factory automation system before, were they are concerned with background noise.
32The RSSI seems to result in a random value, is this correct?
RSSI is appended at the end of the packet. It may vary due to different RSSI readout for each packet.
33The RF module RC1180-RC232. Is there a MSL-level on this product?
We have not been able to formally declare a specific MSL level as semiconductor manufacturers do, due to the module assembly and test process. But we decided to vacuum all full reels that we ship, to stop any moisture exposure under transport and storage before use. We have not experienced any issues with moisture, but was asked by some clients to provide vacuum packs, so we introduced this for all shipments just as precaution.
- Modules have no problem to be stored 4 weeks in an un-sealed ESD-bag or on the reel only at a production plant. If we use the Moisture/Reflow Sensitivity Classification for Plastic Integrated Circuit (IC) SMDs this equals
MSL 2A knowledge, but as the module just contains Plastic integrated circuits and not is such an IC itself, we have not previously used the terms MSL xx or specified this for our modules.
- per today small volumes and first deliveries are/were shipped in non-sealed ESD bags. For volume deliveries we supply the reels in sealed ESD bags.
- After reception at your production plant, 4 weeks storage of an opened bag before production is no problem. We have tested modules stored > 1 year on tape only and SMD mounted them on PCBs, and soldering ability were good (gold plating of LGAs) and there were no sign of malfunction or problems due to humidity encapsulation.
34The receive LED on the eval kit was flashing but no data sent to the PC. Does this indicate a signal was detected but failed on CRC ?
| Yes, the RX LED will turn on as soon as synch detect is done. But if a CRC error is detected, the LED is turned off and the messages is discarded. |
35The problem is when I exit config mode (X command) and the command does not work. How can I know that?
I am afraid, there is no way to get a feedback from the module about the success of X command in RC232. The best way to ensure that _after_ X command the device is in normal mode is to guarantee that _before_ the X command the device was in config mode. This can be controlled by the config pin: pull and release the config pin before you issue the X command.
36The MAX input power is 10dBm. What appen if the module receive a greater power? Just the signal make worse or the module could be damaged? In case could you suggest a protection circuit?
Strong signal will not damage the module, but the module is unable to receive stronger than saturation level given in the data sheet.
37The label on the module reads RC1180 2009 17 2.10 is that a latest one?
The label is related to hardware revision. The firmware revision is only available in the configuration memory using the '0' command. Since the configuration memory is corrupted it's not possible to read out the firwmave revision, and you simply just need to test the '@RC' command. If you send the '@RC' command you will receive one '>' if the feature is included. If you receives 3 '>' you know that this feature is not included, and you need to reset the memory by using the 'M' command.
38The evaluation it RCxxxxHPDK-USB have a config. button – does it means that when try to configure the device need to assert it LOW ? Do you have a programmable version that can be used to assert the config pin to LOW when needed ?
The RTS handshake on your host UART can be connected to CONFIG and be used to control it if UART handshake is not used.
39The Datasheet for RC2500HP-RC232, shows 2 pins: PA_EN & LNA_EN, are they to be used or should I disregard them?
PA_EN and LNA_EN are for test and debug purpose only, and should be left unconnected (open) in normal
40The data packet size requirement is for a fixed 24Byte packet, can the radio be configured for the intended packet size, in order to minimize the ‘on the air’ requirement.
| . The module is 100% transparent and if you send 24 byte to the UART on the transmitter module the receiver will output 24 bytes on the UART. |
41Should these boards transmit and receive data to each other out of the box? Or, must their addresses and channels be configured first?
Yes, the demo kit shall work out-of-the box.
42Should RC1140 be better than RC1180for this application because attenuation on water will be lower a at 433 ?
| Yes, generally the lower frequencies are best range-wise in all matters. A RC1140 with max output power, 10 dBm, will have double range compared to RC1180 at 868 MHz and 10 mW (around 1.2 km vs 600m, line of sight). However, the RC1180HP (High Power) has 500mW, and this will overcome the slight drawback of the higher frequency. So for max range (if required), the RC1180HP will be the best solution. It depends if this is a strict requirement for the customer. |
43Should RC1140 be better than RC1180for this application because attenuation on water will be lower a at 433 ?
Yes, generally the lower frequencies are best range-wise in all matters. A RC1140 with max output power, 10 dBm, will have double range compared to RC1180 at 868 MHz and 10 mW (around 1.2 km vs 600m, line of sight).
However, the RC1180HP (High Power) has 500mW, and this will overcome the slight drawback of the higher frequency.
So for max range (if required), the RC1180HP will be the best solution. It depends if this is a strict requirement for the customer.
44Regarding the RC1740HP-RC232, when referring to the region “worldwide”, what does that mean? What certification is available for “worldwide”?
"Worldwide" means 433 MHz is used in many countries around the world, but there are no true “worldwide” certification. We issue DoC for RED in Europe. Further information on regulation compliance is also found in the data sheet. But for country specific information you need to refer to local national radio regulations and check if 433 MHz is license free and the maximum allowed output power as this may be different. In most regions where this frequency band is allowed, you are only allowed to transmit 10 dBm (whereas the RC1740HP-RC232 can do 27 dBm).
45RC1290 – What is the FCC number and the emission designator? RC110HP – What is the emission designator?
The FCC number for RC1290 is available in the RC1290 Data sheet page 21.
As for Emission Designator you will also find information in RC1190HP and RC1290 data sheet (Bandwidth/Data rate/Modulation etc).
46Question regarding RC232 in Star mode (many to one). If more than node will transmit at same to central point – will RC232 protocol queue data somehow, or there will be collision or data will be lost?
If many nodes transmit to the same “master” at the same timeon RC232, there is likely to have collision already on the RF link, and the messages will never be received. There is no queueing in the module, it handles packets one-by-one. If the packets are too close to each other, some will be lost.
In this sort of applications, the users used to create a randomization on the nodes: i.e. each transmits with a random delay calculated based on their ID, etc. This is to minimize packet loss.
47Please confirm if packet_length should be configured to total number of bytes including overhead (26 in my case) or only effective payload (15 in my case)
The packet length parameter only refers to UART bytes. The RF overhead you do not have to think about.
So you set it to 15.
48Maybe you have some documents or test reports about the influence of the data rate to the range in the same system?
There are some general rule of thumbs that can be used.
Doubling the data rate give 3dB less sensitivity.
4x data rate give 6 dB less sensitivity.
6 dB less sensitivity is used as approximate 50 % range.
2.4 kb/s = x meters
9.6 kb/s = x/2 meters
38,4 kb/s = x/4 meters
Etc.
49It is possible to set either4-Byte or 1-Byte addresses in non-volatile memory?
4 byte dressing is supported by the T command if ADDRESS_MODE=8. Note however that the module reply with prompt (>) for each byte you send. We can see that this is confusing, and we will update the documentation regarding how to use the T command when ADDRESS_MODE=8. Please let us know if this help you out.
50Is there any possibility to replace the 1780HP by a module certified for North America and with the same (or closed) range?
For the US market we recommend RC1290 as this has been RCC approved and costumer can reuse our FCC ID to reduce test cost. We may in future have available RC1790. This will have typ 6 dB better sensitivity but same max output power (-1 dBm) since FCC limits the output power to -1 dBm.
51Is there an acknowledge message/signal on successful message transmit?
The module do not have embedded ack. This must be handled outside the module in the host controller if needed.
52Is the RC11XXHP-RC232 series pin compatible with the low cost family RC11XX? Is there a possibility that the additional pads on the product PCB n31 to n 42, short or connect to a trace or via under the RC11XX module ?
The RC1180HP-RC323 is pin compatible with RC1180-RC232.
Note that the HP variant draw higher current and some of the do-Not-connect pins have different polarity on RC1180HP.
(e.g if you ground a pin marked not-in-use for RC1180, this pin might be used to control PA and will give problem fir RC1180HP.)
There are routing and via on the bottom side of RC11xx, with solder resist covering.
If you have routed signal under module there will only be 2 solder resist film between those line.
If you have bare pad under the module, this is even worse.
53Is the operation with RC1180HP module license free in Germany and in EU?
Yes, you are allowed to transmit 500 mW at 868 Mhz in EU as long as you select your channels inside the high power sub-band (869.4 – 869.65 MHz) and use less than 10% duty-cycles.
54Is the internal configuration (internal diode, internal pull-ups, etc) of RC17XX series the same of RC1240 on same pin? I.e, when pin of RC17XX is (functional) the same of RC1240, the internal configuration is the same too? If there are differt configuration, could you indicate it?
RC12xx And RC11xx/RC17xxHP has different pin properties as the internal MCU is different. Please see data sheet for details.
55Is multihop supported?
No multi hop support, but can be handled by an external host using UART.
56Is it possible to program the frequency between to 240-378MHz?
The RC1180HP cannot be tuned to that band. This is not a license free band. So in order to operate in this band you would need some sort of license.
57Is full-duplex scheme feasible with the modules?
| All of our modules are half-duplex types. In order to have full duplex you will need two modules on each side, operation on two different channels at the same time. |
58In your schematic i can see four connections on the RF Antenna port, A66 0 Ohm Resistor to a LGA Pad, L-Bead to Connector P6, Resistor to UFL Connector P3 ,Resistor to hole. Which of them are necessary for the antenna?
The chosen antenna is selected by soldering in the 0 ohm towards this antenna, the other serial components are then Do not mount. In general, use a shunt and a series element at the output of the RF-pin towards antenna, to allow for slight impedance tuning if required. Add zero ohm towards each antenna if you want to have several options for antennas.
59In the Datasheet of the RC11XXHP-RC232 Module it is written that the Module is “Designed for EX compliance”. What does this mean?
EX compliance components are sometimes required by costumer for end product operation in potentially explosive environment. For details please see:
http://en.wikipedia.org/wiki/ATEX_directive
60In order to save costs, the customer need to make a only one board that can accept the different devices: RC1240 or RC1701 / RC1701HP or RC1740 / RC1740HP or RC1780 / RC1780HP or RC11x. Could you supply a final schematic for all pins (series resistors, pull-up, diode etc.)?
Unfortunately we do not have a schematic supporting all Modules like you request. You need to study the individual data sheet and make 0 ohm resistor network for different pins. Pleaser also see enclosed wsheet inform about pin differences between RC12xx and RC11xx. For RC17xxHP, the pinout is same as RC11xx, bot RC17xxHP has additional pins as described in data sheet.
61In a point to multi point scenario, (host with clients) can the host see the received signal levels of the clients when they transmit data?
Yes, by enabling RSSI append the receiver will measure signal strength and add one RSSI byte as the last byte of the UART message. For details see data sheet page 12
62If more than node will transmit at same to central point – will RC232 protocol queue data somehow, or there will be collision or data will be lost?
If many nodes transmit to the same “master” at the same timeon RC232, there is likely to have collision already on the RF link, and the messages will never be received. There is no queueing in the module, it handles packets one-by-one. If the packets are too close to each other, some will be lost.
In this sort of applications, the users used to create a randomization on the nodes: i.e. each transmits with a random delay calculated based on their ID, etc. This is to minimize packet loss.
63I’ve noticed the label FCC pending on the RC1190HP. Could you please confirm is FCC approved?
No, this label is correct. FCC Pending. This information is also available on our webpage. (https://radiocrafts.com/kb/can-use-rc1190hp-us/)
64I’m not currently using flow control, and am having an issue in correctly identifying the start of each 64 byte packet. My understanding of CTR/RTS is that they wouldn’t help in this? Is there a signal that shows the start of each packet?
| The RC1180 use Asynchronous UART and flow control is no needed on the host MCU as long as the UART speed is correct. The start of the incoming packet will be the first Start bit on TXD.
Optional Hardware flow control lines are: CTS pin – Clear to send: The low-asserted CTS pin provides flow control for the module. When CTS is asserted (low), serial data can be sent to the module for RF transmission. If the module is busy, like during RF data transmission or reception, the CTS pin will be de-asserted (high) to stop any data transfer to the module. RTS pin – Ready to send: When RTS is asserted (low) the host allow data to be sent from the module to the host. The host can stop the module from sending data by de-asserting (high) the RTS signal. Note that if the module has data waiting in the receive buffer, it will not be able to receive or transmit further data until the RTS has been asserted and the data in the buffer is transferred to the host. RXTX pin – RS485 driver control: RXTX is low when the module can receive data on RXD. RXTX is high when the module is transmitting data on TXD and additionally 1 ms for the module to turn from TXD to IDLE mode (see Timing Information in the module data sheet). The RXTX pin is normally connected to the /RE and DE pins on the RS485 driver circuit. |
65I’d like to receive the thermal profiling for the reflow oven regarding your RC1180 and RC1701 modules. I’m looking in your website, but I can’t find this info.
The Soldering profile recommendation is as described in data sheet.
66I would like to know how to use the pins N°27 and 28 on the RC2500HP
Pin 27 and 28 must be left open.
67I want to know if you information about the transmission distance regarding the power RF level ?
Range estimate free line of sight at highers output power and best sensitivity (lowest data rate) is:
- RC2500-RC232: 500 meter
- RC2500HP-RC232: 2000 meter
68I use a switching DC/DC regulator, will the ripple have a negative effect on the VCO in the radio?
It should not influence on the VCO, but the specter might be more noisy if it affect the power amp stage. If the noise is inside the channel bandwidth it will influence on receiver performance.
69I see that the RF Data rate is configurable, but cannot see anything regarding the UART Baudrate, I presume this is also configurable ?
| . Yes, UART baudrate is configurable is steps up to 230400 baud. Default is 19200 baud. |
70I get no more prompt when asserting/deasserting Config line. I use the M command in order to modify different settings.
The use of the ‘M’ command and stable power supply it normally the challenge in these cases.
During the ‘M’ comnmand part of the flash is erase and rewritten. In case of the power supply being turn off at this stage
or limited current capability of VCC this could leave this part of flash in unknown state.
This will make the module seem dead.
1) Limit the use of ‘M’ command to once. (normally in factory and not in field)
2) Make sure that VCC supply and VCC_PA cupply can handle the current without voltage drops.
a. E.g. Some LDO’s have large voltage drop during pulse current. When we erase flash with M-Command it is a pusle current used.
3) Never turn power off close to an ‘M’ command in time.
71I discover that when I start the system, CONFIG pin is low and UART is not initialised. I think it is a mistake and can create some problems. Can you comfirm?
If the config pin is low when you start, all the bytes sent to the module afterwards will be interpreted as commands. This can cause an unwanted configuration change (i.e. M command).
72I can’t find out in documentation, how to change RF data rate in volatile memory only in RC1780HP module. In “RC232 Embedded RF Protocol User Manual v1.5” there is no such command specified
There is no command to change RF data rate in volatile memory for RC1780HP-RC232. Data rate can only be changed by ‘M’ command.
Please note, the RC232 Embedded RF Protocol User Manual v1.5 does not apply to RC17xx series.
73How this lower frequency does effect to the range?
Lowering frequency would certainly increase range.
Compared to 868 it might be double range.
That means at 400 MHz a 21 dBm solution will have same range as 27 dBm output solution at 868 MHz.
74How long does it take for the module to be active after an RF baud rate channel + reset?
Timing details is specified in Data sheet / User Manual. The module is active after a few ms from Reset has taken place.
75How long does it connect to the network (makes connection)? Is it seconds or milliseconds?
A slave/sensor can wake up and do a transmission in milliseconds. TX transmission depends on data rate and number of bytes of course. For a short message << 100 ms (30 bytes at 2.4 kbps)
76How do I know if I am in config mode?
It is easy to detect an anormal entry in Config mode: I just have to monitor the TXD line and see if a prompt arrives (your suggestion). In such case, I send a X command.
77How do I bring the device in config mode without pressing the on board button?
The only way to enter configuration mode is to set CONFIG pin low. From the PC side you can use the RTS line on the UART to set module in CONFIG mode, if you do not use handshake. You must in this strap the RTS line from the FTDI pin to the CONFIG pin on the module. From the PC application you can themn toggle RTS to enter configuration mode. Note however that the Radiocrafts PC application do not support RTS toggling, but if you make your own PC application you can include this feature.
78How can we make a repeater? Do you have a model or we could do it with two modules?
"The repeater functionality is best implemented in a small external controller which takes the received UART data, wait a few ms till the module is ready and then sends the same payload into the modules UART, possibly with
some hop-counter information (and/or I/O readings if required). There is no support for repeater-function inside the module itself.
If you are not deploying too many repeaters (so cost is not that crucial) a simple repeater can be made as described in our application note AN02 "
79How can it be that the latest batch have an older hardware, but newer software?
For small sample requests we ship from different production batches, while volume delivery will go from latest batch. In addition we always ship with the latest firmware revision. For this reason you may occasionally get newer firmware with older hardware batch.
80How can I send a pulse from the module?
Our RC232 RF protocol embedded on the modules are using a UART interface to communicate to an external MCU. Our modules do not have a pulse input that will trigger the transmitter and if this is your request you need to do this in an external MCU. This external MCU can have a pulse input and send a byte over UART to the module. On the RX side the module will receive the byte and send it over UART to an external MCU. This MCU then output the requested pulse
81How can I reuse the CE marking on the radio module for my product?
The use of a CE marked radio module can avoid re-certification of the final product, provided that the end user respects the recommendations given by Radiocrafts. A Declaration of Conformity is available from Radiocrafts on request.
Recommendation is according to Data sheet, User Manuals and dev kit reference design.
82How can I measure Modulation Bandwidth according to EN 300 220-1 section 7.7.2?
Yes we measure average as described in EN300-220-1 section 7.7.2.
"Averaging measurements with 100 samples are possible for constant and non-constant envelope modulated equipment."
83How can I get world-wide coverage in sub-giga frequencies
For world wide I would recommend a combination of module with the same footprint.
Use RC1290 (FCC certified) for US and contries having similar approval
Use RC1780 at 868 for Europe and contries with similar
Basically most contries follow US or EU.
84Have your heard of Modbus… do you have any experience..?
| Modbus is a protocol which normally uses RS485 as the physical layer. Data can be sent transparent over one of our modules named RC1180-RC232 (same part as wireless M-Bus 868 MHz but the protocol is transparent, i.e. sending any modbus-data in one end will cause identical modbus data in the other end). When it comes to the interpretation of the data we unfortunately have very little experience. Only experience we have is replacing the RS485 cable with a Wireless replacement. |
85For RC1140-RC232 Is the total current consumption is: 24mA+35mA = 59mA ?
It is 24 mA in RX and 35 mA in TX , not the sum of the two.
86For EN 300 220, which “receiver category” (1, 1.5, 2 or 3) has been used for conformity assessment of RC1240?
The RC1240 is compliant with receiver category 1.5.
87For a packet size of 24 Bytes, could you provide an estimate of the ‘on air’ time at data rates of 50 and 100 Kpbs?
Timing depends on number of byte transmitted, UART Baudrate and RF data rate. The module adds some additional bytes on the air (2 Byte Preamble/synch, 2 byte address and 2 byte CRC).
88For a new project I would like to obtain an ultra long range, better than the RC1780HP
You will egt better range than RC1780HP if you select RC1701HP. This runs on 169 MHz and will have typ 5 times the range of a 868 MHz solution if all other parameters are the same (Output power and data rate, channel bandwidth). UNB stand for Ultra narrow band and is supported by RC17xxHP family.
89For a limited space – is there any antenna that you could recommend? Preferably not longer than 3 cm.
For antenna we use the standard antenna included in our kit.
for smaller size antennas at 433 MHz you may use a chip antenna. Fractus has som options.
90Each slave boat will have a bit rate of 1Kbps to the master node, the signal range must be till 2km (line of sight). We are considering using RC17xxHP-RC232 modules to communicate with master boat and slaves. It’s possible with this device to create a multipoint network (one master, many slaves)?
It supports one master many slaves. Please see RC232 User Manual for details about the embedded protocol.
91Does your module comply with CE, WPC, FCC and ARIB?
For CE marking, self-declaration is sufficient. For FCC and ARIB and WPC, the RF should be certified as part of the complete product. We have done pre-qualification so we know the module will meet the respective regulations. Attached is our Declaration of Conformity.
92Does your module (RC1780HP-RC232) have frequency hopping function?
Frequency hopping is not included in the protocol, but it support channel configuration so that you on the host side can implement multi-channel system.
93Does the module comply with EN 2010:62479?
This seems to be applicable only to human exposure of radiation, we assume below given limits. We have not tested compliance towards this, but we will assume a solution with the module complies. As far as we know, the –HP version of the module must have somewhat reduced output power, but not the RC2500 itself.
94Do your radios have any kind of Listen Before Talk feature ?
| The RC1780HP has two option of Embedded firmware. That is RC232 protocol or Tiny-Mesh protocol. You can read more about differences on the web. The RC1780HP-TM includes support for LBT while RC1780HP-RC232 only support RSSI readiong and you need to include LBT in your host controller. |
95Do you use a CCA/MA that’s in error or drifts like RSSI? What is your proposed solution for this issue?
The RC232 embedded protocol is not including CCA, but RSSI command can be used by the host controller prior to transmission to check if the channel is free.
96Do you have any application note about using modules in a RS485 bus?
Application note for using the RS485 bus in not available.
97Do you have an Unlimited modular approval FCC / IC + EN Test results?
We only have a self-declaration according to EN-norms, as stated in the DoC. The test report is available, based on conducted measurements and estimated radiation parameters, based on a practical antenna.
FCC modular approval is not obtained for the module, only pre-scan according to FCC standard
98Do you have a FCC ID for the RC2500HP module?
The RC2500HP has been tested towards FCC regulations for license free operation under part 15. However, a final approval is required by FCC for the end product. For this reason FCC ID is not available for this module. For details please see data sheet.
99Do you consider that the 2.4Ghz antenna alone allows to reject the GSM signal to prevent damage on the RC2500 ?
I do not think the module will be damage by the signal from GSM module, but link can be reduced If used a t the same time. I guess you can control this in the application and ensure not GSM and Radiocrafts operation at the same time. Antenna will not filter much on the GSM signal if the GSM operate at 1800 MHz. You might look into use a 2.4 GHz SAW filter for better filtering. Your functional testing will decide if needed.
100Do RC232 series offer automatic baud rate detection?
The module do not support auto baud rate detection. If you do not know the Baud rate of the module you can try to read back the ‘>’ value when pushing CONFIG low for different host baud rates. When you detect ‘>’ you know that the host baud rate is correct. Alternatively you can measure the ‘>’ duration using a oscilloscope and estimate the baud rate of the module.
101Designed for EX compliance. What does it mean?
Designed for EX compliance ensures that the module can be used in any EX application.
EX area defined by www.iecex.com as:
“Ex areas can be known by different names such as “Hazardous Locations”, “Hazardous Areas” “Explosive Atmospheres”, and the like and relate to areas where flammable liquids, vapours, gases or combustible dusts are likely to occur in quantities sufficient to cause a fire or explosion. The modern day automation of industry has meant an increased need to use equipment in Ex areas. Such equipment is termed “Ex equipment”.
102Could you send details on how broadcast and unicast routing works? Is a mesh network or hopping supported, if so to what size?
The RC232 protocol is a point-to-multipoint protocol that does not support mesh/multihop.
103Can you support low qaulity (not HiFi) audio with RC232 over 868 MHz
Theoretically yes… you may compress and code the audio signal to 10-20 kbps and do a time duplex protocol to get two-way audio link. But it’s not a killer application for us, the modules are not really targeting data streaming as in audio/voice.
104Can you please suggest us how to read the set value of PWM?
I’m afraid there is no command specified to read the current PWM value.
105Can you please confirm the width of the PCB trace from the RF pin of the RC1140-RC232 to the copper pad we use to connect a wire antenna in order to achieve 50 ohms Z0? We’ve also done the layout so the power plane has a cutout below the microstrip.
There are several microstrip calculators online and they have always given correct results for me.
What happens in the power plane is not important to the microstrip.
106Can you give a guidance on the range in a city and non-line-of sight?
I would guess the range you would see with RC1701HP-RC232 would be 500-1000meter operating at low datarate. Typical 2.4 kb/s.
107Can we request modifications to the RC232-protocol for additional features?
Yes, we are able to provide costumer specific adjustments to the standard RC232 embedded protocol. Price and delivery time will depend on complicity and volume order.
108Can we mix RC1280 and RC1780 if possible in the same networks
| The RC1280 and RC1780 are not compatible over the air. |
109Can we have the power consumption on RX mode (standby mode, waiting for any RX to come) be as low as 2-3 mA? (On the spec it is 24mA)
The RC232 Idle power consumption is 22 mA since the radio is up listening 100%. If you have strict requirements on ultra low power you can implement the application in order to save power. This is for example to have battery power devices to sleep most of the time (RF RX off) and periodically send message to the master. Alternatively send a beacon before receiving information. In most application this approach is doable since normally only on side of the link is battery powered.
110Can two gateways communicate with each other?
No, that is not possible.
111Can RC232 module be used as a router/range extender device?
RC232 does not have this feature.
112Can I use the RC1190HP in US?
No, Challenge is that RC1190HP is not FCC certified, and cannot be without frequency hopping.
113Can I reset the slave RF Modules by Master by sending a command through RF?
Remote factory reset is not supported by the RC232 protocol, and must be handled by host controller.
114Can I reduce the time when using the S command to read the RSSI? It takes 19ms
Please note that RC1680HP has two different RSSI reading in configuration mode. The commands are ‘S’ and ‘s’. The Small s should be used for fastest response time as it is typ 1.6 ms compare to S response of 19 ms.
115Can I load my own FW on the module?
We do not support API interface for costumer to add their application inside the module and still use our wireless protocol. If you want to use the module only as a hardware platform you must implement the whole embedded wireless protocol yourself without any support from us. There are also limited to the resources on the specific MCU we already have selected it to be used only for the Wireless protocol.
The fastest and easiest way to a wireless implementation is to take benefit on our already industry proven wireless protocol, and select an external host MCU for your application. They communicate with the module using a UART interface.
116Can a software update / bootloader command be added? We need something that allows us to update the RC232 module in the field via the UART.
Some pins are allocated for firmware upgrade possibilities of the Embedded RC232 protocol. See Data sheet page 19 for details at https://www.radiocrafts.com/uploads/rc11xx-rc232_data_sheet_1_42.pdf. How to firmware upgrade the module is described in AN012 at https://www.radiocrafts.com/uploads/an012_firmware_upgrading_the_rc1180_mbus_module_1_0.pdf.
117Can a channel scan feature be added?
This can be added or you can use the UART command and check channels for RSSI by your host controller.
118Are the Settings made during Configuration persistent, or do these settings need to be made each time the device is powered on ?
| Settings in configuration memory is stored in flash and kept after power cycle. Due to flash write limitation we also include some RAM command for parameters to be changed regularly. See User Manual for details. |
119Are the RC1140 and RC1240 compatible
No. They are not compatible.
120Are the modules full duplex ?
Module is half duplex. Sent and receive but not at the same time.
121Are RC17XX and RC17XXGP pin compatible?
Yes, RC17xx and RC17xxHP is pin compatible. Only difference is that VCC_PA is only in use for RC17xxHP.
122Are all the connections on P5 necessary for a Microcontroller? Or are the pins Config/TXD/RXD/GND sufficient?
Only pins required are TXD and RXD (along with VCC and GND of course), but for flexibility, connect also Config, Reset and CTS (for larger packages and flow control required).
123Actually we want to change the SID of a gateway which is already installed. How to change the SID?
SID is stored at address 49-52 in the configuration memory as described on pp. 63 of the datasheet. It is not necessary to use the RCTools-TM itself. You can use any uart tool/MCU and applying the ’M’ command there. Alternatively, have a look at page 26 “Transmitting command and configuration packets from Gateway”.
124According to your datasheet, the maximal RF rate is 4.8 kbps. If I use more, the BW will be greater than 12.5 kHz and it will not be possible to have 8 channels in the band.Can you comfirm this fact?
Yes, I can confirm that combination of high power (869.4 to 869.65) and 10% duty cycle and high data rate is not possible to combine with 8 channel.
125If the module is powered down when not required for RX/TX, what is the power up time before it can be used to transmit? – is there failsafe way which indicates WHEN the module is ready to transmit, or determine this by checking something?
2. Power up time is in the order of 5-10 ms. If the Config pin is activated during power on, the module will enter Config mode and send a promt “>” when ready. You may then exit by “X” and send data.
126How does the RC1180-RC232 react as the supply voltage reduces below the minimum operating voltage and below – the system is powered by a Solar cell secondary cell to hold charge short to medium term. It is possible the secondary cell will start to discharge beyond the requirement for operation – does the module need to be unpowered to protect it from brown-out situations.
1. If the voltage drops under a certain limit, which is lower than the min operating voltage, the internal brownout will do a reset. Another way, to define this more accurately is to use a dedicated voltage supervisory circuit to control the Reset pin. Or even the main MCU may do this.
127When I connect to the development board using your software (“”RC232 Configuration and Communication Tool””), everything works fine. But when I connect to the development board from inside my own application for the first time each day (e.g. in the morning when the dev. boards have been powered down for a couple of hours), it only sends 0x00s via the air interface, no matter what i want to send, everything is zero. When I then connect to the board once with your software, everything works fine again and also my application afterwards works fine, and I can send everything correctly again. But I have to do this every morning again. Maybe you have any ideas what the reason for this is or what I could do to fix this problem?
"This is the following pseudo code that RC232_CCT is running just after the serial port is opened:
Write 'X'
Set RTS high
Discard Input Buffer
Discard Output Buffer
If you still have problem running your application the first time, try to hardware reset the RC1240DB using the RESET button on the board.
"
128We use the RC1280HP would like to know if an LNA could help improving the Rx signal of the RC1280HP. Could you give us some advice on that?
Yes, it will help improve the sensitivity but also make the module more vulnerable to saturation if a strong signal from a neighboring transmitter is present. But if they always have weak signals (long distance) then this LNA will improve the sensitivity. The theoretical percentage increase in range I would have to investigate further but it should be pretty significant if they are comparing line-of-sight values.
129We need to cover a LOS of up to 1Km While having the antenna approx only up to 1m above ground level. Can this be achieved with RC2500-RC232 with 1dBm output?
For 1 km range I would go for the RC2500HP (If you need to do 2.4 GHz, 868 is an alternative for EU)
130We enable the RTS/CTS option in the DK and we send message longer than 128 bytes (the max buffer size) so we need the CTS to separated the massage. We test this with scope: 1. In the CTS we didn’t see change (I suppose all 128 bytes it needs to change) 2. Also in the Tx/Rx I suppose to see a break in the 128 bytes, but it takes all the massage 3. When I try connect this module to PC, only message shorter than 1024 bytes success to send
"The CTS is proven to work well. Note that it goes “high” for only a few ms (while the buffer is emptied via RF) and then goes low again, when the module is then able to receive UART data.
One test you can do is to change the packet size (buffer size) to like 2 bytes and then send 128 bytes, then you will see the CTS going high after each 2nd byte, and if the host works properly all 128 bytes of data will come through 2 by 2 bytes (note that you must of course also configure your host Telnet of HyperTerminal of whatever to work in hardware handshake mode).
It is possible that your host must be configured for 2 stop bits in order to catch the CTS signal otherwise it might act too slow to the CTS going high. When everything is configured correct, we have sent large data files of several kB
via using the CTS signal for controlling the UART flow.
"
131We claim in our documentation 500-600 meters LOS. It looks like we are half of expected range What are your explanations regarding this performance difference;
| If you are not able to reproduce 5-600 m, the explanation must be: a. The TX is not correct, to low output power b. The RX sensitivity is not correct c. The test area is not LOS, or there is too much background noise. Packet length should be 20 bytes (including overhead/CRC). |
132We are drawing a new board which used your module RC1180. We are in a final phase. For the interface with the our µC, we connected only the pins : – RxD & TxD for module configuration and normal use for communication – Pin Reset, Pin 19, Pin 20 : for future programming (case of firmware update) Also, we connected the pin Vcc and ground with recommandations described in your data sheet. I would like to know, if we can use functions of test carrier transmit, modulation transmit and permanent receipt with only the pins RxD and TxD (RTS, CTS and config not connected to our µC but available on test pads). Do you have a procedure to put this module in test mode. For a firmware upgrade, could you confirm us that we need only Pin 19, 20 and reset ?
"It is correct that you only need RxD and TxD for module configuration and normal use. CONFIG, RTS and CTS are optional.
To set the module in test mode you need to enter configuration mode by sending 0x00 to RxD and wait for ‘>’ (0x3E) on TxD . Then enter Test mode 1 you send ‘1’ (0x31) to RxD and wait for ‘>’ (0x3E) on TxD again. Optionally you may enter config by assert CONFIG pin low instead of sending 0x00 on RxD.
For firmware upgrade you need Pin 19, pin 20, Reset, GND and VCC as described in the datasheet page 16.
"
133We are currently evaluating your RF Modules RC1180-RC232 and RC1180HP- RC232. I stumpled upon two important questions: Are those two modules interchangeable? Can a RC1180 communicate with a RC1180HP and vice-versa? Are they pin- and software-compatible?
Thank you for your interest in our product. The RC1180-RC232 and RC1180HP-RC232 are pin compatible, but you must pay attention to the power consumption differences if you want one board with drop in replacement support. The Board power source and regulator must be designed for The RC1180HP-RC232 since this has highest peak current in TX mode.
134we are building an application with one master boat, which communicates with 150 slaves boats (obviously in open sea). Each slave boat will have a bit rate of 1Kbps to the master boat, the signal range must be till 2km. We are considering using RC17xxHP-RC232 modules to communicate with master boat and slaves. Our questions are: It will be the RC1780HP-RC232 module suitable for this application, or you propose some other module? It’s possible with this device to create a multipoint network (one master, many slaves)? Does your modules have frequency hopping function?
RC1780HP-RC232 is a excellent choice for your multipoint network. It supports one master many slaves. Please see RC232 User Manual for details about the embedded protocol. Frequency hopping is not included in the protocol, but it support channel configuration so that you on the host side can implement multi-channel system.
135The data rates for the high speed module RC1180HP is more suitable for our needs, but we need to have the possibility to increase the range with a high gain antenna or any kind of amplifier, could that be possible?
| In order to comply with European regulation the max radiated power is limited to +27 dBm in the license-free 868 MHz band. This is the max output power of RC1280HP and RC1180, and you can for this reason not increase the range by using a high gain antenna or amplifier because the output power will exceed max limit |
136Please confirm that: RC1180/1140 and 1190 have exactly the same foot print/pin out… The goal being to have only one PCB and the same print for the 3 modules.
The fooprint and the software is exactly the same on these modules.
137Our company currently use the modules 1280HP of 500mW. We need to amplify more, is there the possibility of more than 500mW with an external amplifier?
| 500mW is the max output power allowed in EU to comply with EN300220 at 868 MHz. For this reason we do not have a module for higher output power than 500mw. |
138Non-volatile memory contains the module name and version (e.g. “”RC1240,2.60,2.34″”) starting at offset 0x3C. The manuals don’t mention it, is this string present in all modules at the same address, and can we use it to identify the module?
Yes you can, but as this is not documented I do not think we will issue an Release note if/when we change this. We use this data ourselves in our PC-tools.
139Is it possible to setup a maximum length for received packages in RC232? I am aware of TX packages can be configured to have a maximum package length. By being able to configure the maximum length of received packages, I can have a smaller rx buffer size to store it in while processing it.
It is only the TX Packet length that is configurable, but as long as you have control of the Packet length of the transmitter you will indirectly also have control of the RX buffer size.
140i have some questions for RC1701HP-RC232. Need the “tx” pin a levelshifter or driver-ic (our previous experience with RC1280 was a f—ing 100KR impedance!!!) ? Are on the “tx”, “rx” and “cts” pins resistors in series? Can I connect “tx”,”rx” and “cts” directly to a MCU (XMEGA @ 3,3V)?
RC1701HP is supporting 3.3V I/0 directly to/from 3.3V MCU and no additional driver is needed. For MCU consideration please see data sheet page 8 for details.
141I have problem to wake up RS1240 from sleep mode, in fact I can’t wake it up at all. According to documentation, config pin should be asserted when going to sleep mode, and then positive edge should wake ip module This is code I use: Config Portd.3 = Output : Modem_config Alias Portd.3 Modem_config = 1 ‘ ———— PUT MODEM IN SLEEP MODE Modem_config = 0 ‘ Assert Config pin Waitms 5 ‘ MAX Time from CONFIG pin is set low until prompt (“”>””) Print “”Z””; ‘ Goto SLEEP mode . . . Sub Send_packet Modem_config = 1 ‘ Wake up form SLEEP mode Waitms 60 ‘ Wait 60 ms to get out from sleep mode Print “”X””; ‘ Goto idle mode Led_tx = 1 Printbin Paket_start Printbin Data_packet Led_tx = 0 Modem_config = 0 ‘ Assert Config PIN Waitms 5 ‘ MAX Time from CONFIG pin is set low until prompt (“”>””) Print “”Z””; ‘ SLEEP mode End Sub But, module stuck in sleep mode, and dont send enything. When I comment all lines regarding sleep mode, module work fine. Where I’m wrong? I should deliver device this week, and this is only problem I have to resolve.
Instead of the “waitms” in your code you should use a “wait for prompt” routine or at least increase the wait time period. The timing information in the data sheet is typical values and we recommend to wait for prompt “>” to ensure that you are in configuration mode before the ‘Z’ command is sent to the module.
142I have a question for the RC2500HP-RC232, which seems not to be listed in the datasheet. We have the RC2500HP-RC232 connected to a supply voltage of 3.3v. Which voltage will the uart tx output from the RC2500HP-RC232 be? We found a other note on your site, that suggested that it would only have 2.7v on the uart tx pin, even though the module was supplied with 3.3v.
"Look at the RC2500HP-RC232 datasheet;
and on page 3 it is tried to visualize that the output pin TXD is pulled to VCC when high. So if VCC=3.3V, then TXD will also be 3.3V.
"
143I bought the RC1180RC232DK (USB). Need quickly connect both modules to RS232 lines, to made a wireless path between angle-sensor and test PC. The actuator should only send each packet (packet of 4×8 bit angle values) to connected PC. Always active after power-up. Is enough to disconnect the jumpers from/to Rx/Tx lines and connect the module direct to RS232 level shifter? (inverted?)
Yes, you can remove the jumpers on P13 and connect a RS232 level converter directly to the RXT/TXD pins of the module (START bit low and STOP bit high). Board details in the kit User Manual
144For a packet size of 24 Bytes, could you provide an estimate of the ‘on air’ time at data rates of 50 and 100 Kpbs. PilotAware is a co-operative broadcast system, and hence the minimum amount of time on the air is crucial.
| . The module is 100% transparent and if you send 24 byte to the UART on the transmitter module the receiver will output 24 bytes on the UART. |
145[RC232 Which modes are used in the RC232 protocol?
The RC232 protocol has two modes.
Configuration or traffic. In traffic mode the radio is transparent. So the bytes sent into one module (UART) comes out on the UART at the opposite module.