Narrowband Q&A
Enter your keywords to find answers:
Technical questions from customers, answered by Radiocrafts' support engineers, about narrowband modules.
No questions match your filter.
01What range can be achieved with a narrowband radio?
The RC12xx and RC17xx series, as well as the RC16xx Sigfox modules, are all narrowband. The range depends on the output power and frequency. Some of these modules reach 20 km and more in open field tests. See the Product Number Overview for a summary of range and performance.
02What is the effect on range if I use higher data rates to reduce the transmission duration?
There are some general rule of thumbs that can be used: Doubling the data rate give 3dB less sensitivity. 4x data rate give 6 dB less sensitivity. 6 dB less sensitivity is used as approximate 50 % range. Example; 2.4 kb/s = x meters, 9.6 kb/s = x/2 meters, 38.4 kb/s = x/4 meters, etc.
03What is the drawback of narrowband radio? What about the temperature range?
The obvious drawback is the limited data rate. Further, the frequency of transmitter and receiver must be close to identical due to the small bandwidth. Because of this there must a temperature compensated crystal oscillator (TCXO) in narrowband transceivers. The TCXO used in RC17xx series has a given accuracy in the -30/85 degree range that we utilize. The TCXO does operate functionally down to -40, but then with slightly more variance and possible degradation in sensitivity.
04What is the difference between RC12xx and RC17xx series?
The RC12xx series is a series of compact low power narrowband modules with competitive pricing covering most 400/800/900 MHz band applications meeting regulations in Europe, US, China, Korea, Japan etc. The RC17xx series is a new module series in the same compact form-factor also adding high power variants and a VHF frequency option at 169 MHz. The performance in term of sensitivity and selectivity is even higher for the RC17xx series.
05What is the difference between RC1180HP and RC1780HP?
RC1180HP is a wideband/normal transceiver. This means limited sensitivity and no special protection toward interference. RC1780HP is a narrowband transceiver. This means much better sensitivity and much more robustness vs interference. This is due to narrow RX filtering. Due to the narrowband technology this type of radio is often preferred in industrial application were reliability of link is critical.
06What is Narrowband?
Narrowband is a term used to describe radio systems that use a narrow frequency band for wireless communication. The signal bandwidth is typically less than 25 kHz to be called a narrowband system. The benefit of a narrowband system is reliability and range.
07Is Wireless M-Bus narrowband?
Mode N in Wireless M-Bus is narrowband using 12.5 kHz channels at 169 MHz.
08Is the new “NB-IoT” a narrowband system?
Although NB stands for narrowband, the radio system is not narrowband in the normal use of the term (as used in ETSI EN 300 220, for example). As NB-IoT is using 200 kHz channels it is not narrowband as commonly known, but it is for sure much more narrow than the bandwidths typically used by cellular based systems (GSM, GPRS, LTE etc). Hence, they do not achieve the same benefits as with a real industrial grade narrowband system such as implemented in RC12xx and RC17xx series of modules from Radiocrafts.
09In the RC1692HP datasheet I found information that input current equals 59+297=356mA
(VCC=3.3V, VCC_PA=5V, RF output power 27dBm) while the module is sending data, how can I supply it?
The power supply circuit must be able to deliver the peak current, either from the DC/DC converter, of by using a super-cap to help buffer the charge. It is important to check that the supply voltage does not drop during the transmission.
10Do you have a narrowband radio with more than 1W output power?
We offer RC1701VHP module with 1W output power at 169 MHz. For 400/800(900 MHz band, the maximum output power is 500 mW. But an external power amplifier can be added if required, and permitted by local radio regulations.
11Can I use narrowband with frequency hopping protocol?
Yes, narrowband radio can be used with frequency hopping. Currently we do not offer frequency hopping protocol on our narrowband modules, but it can be done by the host controller.
12Can a narrowband radio be used in India?
Yes, all our narrowband radios that are otherwise compliant with the frequency regulations can be used in India. The 865-867 MHz band allow up to 200 kHz bandwidth, and the narrowband radios use 12.5 or 25 kHz, which is well within the limits. Even a general wideband module can therefore also be used, such as RC1170HP-RC232.